Faux Stamped Metal
Check out today’s card design that shows off the super fun faux metal technique.
It all starts with a challenge, Yo!
Does that make me sound hip, cool, dope? Yeah, probably not.
The As You See It Challenge Blog has a theme for us this week.
I wanted to use a technique that I haven’t played with for a while – faux metal. But it should actually be called “faux stamped metal” because stamping into metal is an actual real thing (all the pretty jewelry!). My card uses Copper Foil, Copper Metallic Thread, and Copper Embossing Powder along with the beautiful florals from the Petal Promenade Designer Series Paper and the Wonderful Floral Framelits Dies.
The card base is Old Olive cardstock, but I ended up working with a 4″ x 5-1/2″ card front rather than my usual 4-1/4″ x 5-1/2″ simply because I cut my next layer narrower than I liked and trimmed the base to fit. I think it looks nice a bit narrower – there’s a slightly increased delicate flair to the design. The second layer (the one that I cut narrower by accident) is Mossy Meadow cardstock, die cut using the edge die from the Wonderful Floral Framelits. So pretty! The third layer is a square piece cut from the Petal Promenade Designer Series Paper. This paper pack has a few sheets which, instead of being a typical full 12″ x 12″ patterned piece of paper, are designed to be used in specific pieces. This square was among 6 squares on the sheet of paper. There were also rectangles and a beautiful floral edge piece that I will use for future crafty projects.
Before adhering the Mossy meadow piece to the card front, I attached the Petal Promenade paper and wrapped a piece of the Lemon Lime Twist ribbon from the Organdy Ribbon Combo Pack around the two pieces of paper.
This ribbon is one of the many items that you can earn for FREE with a $60 purchase of things you know you’re going to buy anyway! (you KNOW you will!!)
I tied the Old Olive Linen Thread (NEW! I love this stuff!) around the Organdy Ribbon in a big ol’ loopy bow!
The Wonderful Floral Framelits dies played their part beautifully for the next layers. Sahara Sand cardstock for the chubby oval, Lemon Lime Twist and Mossy Meadow cardstock for the leaves and Powder Pink for the flower buds. Tucked in behind all that is a strip of Copper Foil paper with hand-cut flagged ends.
Finally, the faux stamped metal piece and the loopy Copper Metallic Thread are attached with Stampin’ Dimensionals over the stems of the leaf collection.
Have you tried creating faux metal before? It takes a little bit of time, but it’s not a difficult technique. Start with punching out a piece of Basic Black cardstock with the Darling Label Punch. The colour of cardstock doesn’t matter, since it will be completely covered with embossing powder. Place the punched piece of cardstock on your Grid Paper and apply Versamark ink to it by pressing the ink pad directly to the paper. Pick up the paper with your craft tweezers and dip it in Copper embossing powder. Still holding it with the tweezers, heat set the powder as you normally would, but then you repeat that process two more times. Yup. You want that embossing powder three layers thick for the next part of the process. Don’t worry too much about the marks left by the tweezers – that will be taken care of with the final heating that comes next.
After applying the three layers of embossing powder, place your embossed piece of cardstock on a heat resistant surface (I use a piece of tile). Again, use your Heat Tool, this time straight above (perpendicular to) your paper so it doesn’t blow away. Heat it until the tweezer marks blend into the rest of the embossing powder and you can see that the powder is fluid and moving with the wind of your Heat Tool (I hold it about one inch away from the surface). Then, without delay, set your Heat Tool aside, grab the stamp and press it into the soft, warm embossing powder. Hold it there until the embossing powder sets a bit, then peel the stamp away from the paper. This will leave an impression of the stamp in the embossing powder, just like stamping on real metal would leave the impression of the stamp in the surface of metal! I used the hello stamp from the Darling Label Punch Box set.
Now that, my friends, is “dope”, Yo!
Check out my online store if you live in Canada and are interested in ordering stamping supplies. I KNOW you can do this dope technique, too!
P.S. – If you’re wondering about any damage that you might cause by putting your stamp into hot embossing liquid, not to worry. I held a class where 7 participants each used the same photopolymer stamp with this technique. After the class, I stamped the same stamp on some cardstock and it still stamped beautifully.
